| Author |
Thread: HELP!!! Wiring my amp and subs PLZ!!!!!!!! |
    
New member Username: Fatass_tony
Post Number: 4
Registered: Jan-05
|
| Posted on Tuesday, February 01, 2005 - 11:22 pm: |
|
I purchased one 12" Pioneer Premier TS-W2000SPL which is 2000w MAX and 750RMS, and i also got a 600w JBL amp JBL BP600.1 which runs an Output 2 Ohms: 600W x 1, how do i correctly set up this system to get MAX clean bass out of it. |
|
|
|
New member Username: Fatass_tony
Post Number: 5
Registered: Jan-05
|
| Posted on Tuesday, February 01, 2005 - 11:26 pm: |
|
Ogh and it also Outputs 1 Ohm: 600W x 1, so apperantly its one ohm stable, any way to use that to get more bass out of it, im guessing not since the amp is 600watt maz, just making sure. |
Silver Member Username: James1115
Wilton,
Ct
Post Number: 402
Registered: Dec-04
|
| Posted on Wednesday, February 02, 2005 - 09:49 am: |
|
what is the voice coil configuration on your sub? |
New member Username: Fatass_tony
Post Number: 6
Registered: Jan-05
|
| Posted on Wednesday, February 02, 2005 - 12:43 pm: |
|
# Double 4-Layer, Long Voice Coil (2 x 4ohm)
# 4-Slit Glass Imide Voice Coil Bobbin
# 1-Piece Rubber Gasket
# 750 Watts RMS/2000 Peak Power
# Dual Voice Coil Design (2ohm or 8ohm)
# Frequency Response: 18 - 2kHz
# Sensitivity: 89dB (1W/1m) |
Silver Member Username: James1115
Wilton,
Ct
Post Number: 427
Registered: Dec-04
|
| Posted on Wednesday, February 02, 2005 - 01:22 pm: |
|
well you can run it parellel @ 1ohm but you are underpowering them quite a bit. I would get 1 more JBL bp 600.1 and run them both one to each of the subs. |
New member Username: Fatass_tony
Post Number: 7
Registered: Jan-05
|
| Posted on Wednesday, February 02, 2005 - 01:35 pm: |
|
You must not have understood me correctly, im only planning to power ONE "12 sub, so i wanted to know if there is a specific efficent way to do it. |
New member Username: Fatass_tony
Post Number: 9
Registered: Jan-05
|
| Posted on Wednesday, February 02, 2005 - 07:45 pm: |
|
bump |
Silver Member Username: James1115
Wilton,
Ct
Post Number: 440
Registered: Dec-04
|
| Posted on Wednesday, February 02, 2005 - 09:19 pm: |
|
ok my bad yes run it in parellel at 2ohms should sound good. |
Silver Member Username: Lbeckner
Tulsa,
Ok
Usa
Post Number: 258
Registered: Oct-04
|
| Posted on Wednesday, February 02, 2005 - 10:25 pm: |
|
bump |
|
| Posted on Wednesday, February 02, 2005 - 11:27 pm: |
|
Your info is wrong. The JBL BP600.1 puts out 600W @ 2 ohms, so wire your voice coils in parallel for a 2 ohm load. |
Silver Member Username: James1115
Wilton,
Ct
Post Number: 447
Registered: Dec-04
|
| Posted on Wednesday, February 02, 2005 - 11:34 pm: |
|
thats what I said Anon! |
