| Author |
Thread: PRE-PROGRAMED......PANSAT 2500 RECIEVER |
    
|
| Posted on Saturday, February 19, 2005 - 10:26 am: |
|
Fisherman it's good to see you got that figured out but you need a TWIN LNB not a dual. |
|
Relevant Product Info
|
|
|
| Posted on Saturday, February 19, 2005 - 10:39 am: |
|
a twin is for 2 satellites
a dual is for 1 satellite and 2 receivers
|
|
| Posted on Saturday, February 19, 2005 - 10:54 am: |
|
I see= RIGHT
|
James Explain Unregistered guest |
| Posted on Saturday, February 19, 2005 - 11:54 am: |
|
James why does the above link http://www.dss-jmvip3mfiles.com/forum1/ go to http://expressvukeys.netfirms.com/ |
|
| Posted on Saturday, February 19, 2005 - 12:07 pm: |
|
Fisherman...with the oval DTV 2 LNB dish, U can get both the 110 and 119..U must align each LNB correctly...go to the dish pointing area forums at www.dsscommunity.com ...it will tell U how to align the dish to get both satellites.. |
Bronze Member Username: Knee_grows_back
Post Number: 56
Registered: Jan-05
|
| Posted on Saturday, February 19, 2005 - 12:41 pm: |
|
don't do it.....he's just after your email...going to sell it to spammers..you've been warned!!! |
|
| Posted on Saturday, February 19, 2005 - 01:03 pm: |
|
fisherman...read this link...it'll help U to get more dish pointing help from the links inside..
http://forum.ecoustics.com/bbs/messages/2/120764.html
and don't listen to kneegrow,dsscommunity does NOT spam or sell email lists ...go there as a gues (unregistered) and ask EVERY member,they will tell u the truth..
Kneegrow..U're a loser who I banned from there...keep it up and remember I have your IP logged!and saved right in front of me... |
|
| Posted on Saturday, February 19, 2005 - 04:25 pm: |
|
LK,
Thank you for the help. I'm afraid that I will have to make do with my new round dish and a single LNB for now. I am disabled and on SSI. I committed four months cable bill to buy what I have and until I can pay my credit card off I don't intend to buy more. My loss, I realize. I didn't know so when I saw a NEW DTV dish with Dual LNB for $14.00 on e-bay I grabbed it. With s/h it only cost thriry dollars. I thought I had a deal. I do. With Digital Computer Solutions price of $159.95 for the Pansat 2500a, delivered and the $34.00 for the dish I have less than $200.00 in a system to replace $43.95 a month of non-digital cable with no premium or PPV. I am trying to figure out how to get USA, TVL, TBN, TBS, WGN...and all to come on. The screen tells me "bad or scrambled channel" but I can see a hundred PPVs and HBO, SHO, TMC, STARZ, ENC. I prefer to watch DISC and TVL along with PBS, a movie once in awhile is okay but not so important to me.
fisherman@iname.com |
Silver Member Username: Jmill1948
Chester,
Va
Usa
Post Number: 538
Registered: Apr-04
|
| Posted on Sunday, February 20, 2005 - 06:40 pm: |
|
James Explain
Unregistered guest
Posted on Saturday, February 19, 2005 - 11:54 am:
--------------------------------------------------------------------------------
James why does the above link http://www.dss-jmvip3mfiles.com/forum1/ go to http://expressvukeys.netfirms.com/
I just noticed that.it has to be the expressvuy guy <gordo> trying to pick up my customers...what a jerk.....................jmill |
|
|
Unregistered guest |
| Posted on Tuesday, February 22, 2005 - 08:23 am: |
|
can i get the 61.5 ? with pansat? |
|
| Posted on Tuesday, February 22, 2005 - 10:17 am: |
|
yes U can get 61.5 ..U can get almost any satellite with pansat..its your dish and location thats more important....go to www.lyngsat.com for satellites,channels,etc.. |
|
| Posted on Tuesday, February 22, 2005 - 02:01 pm: |
|
plinio...read this link for Dishnetwork Echo 3 at 61.5...here's the available channels..
http://www.lyngsat.com/packages/dish61.html |
New member Username: Timscarlet
Dayton,
Oh
Usa
Post Number: 1
Registered: Feb-05
|
| Posted on Tuesday, February 22, 2005 - 06:52 pm: |
|
Seting Up FTA Receiver and Dish for Dish Network find files on internet...
Note : This is for the Pansat 2500a receiver. You may have to download a different
flash and downloader if you have a different receiver type.
1. Connect satellite receiver to PC with RS-232C straight cable (Not Null Modem) or a serial cable with a male to female adaptor.
2. Turn on the power in the back of the satellite receiver. Don’t turn on the power button in the front of the receiver.
3. Open the (2300_2500_1500 Downloader)
4. Click “STB MODEL” and type model name exactly key:global
5. Click “BIN FILE” and select the (X-8500_2500A_10_05_04) bin file located in the flash folder. Or the newest flash.
Note: Use the Factory Flash (Pansat 2500A_040607_222_api(N) for basic FTA or if something goes wrong and you need the original flash. Go to www.pansatusa.com for the latest flash for your reveiver.
6. Do not interrupt while downloading. Make sure your Computer says "Download Complete", not just 100%. If you don't get "Download Complete" you have NOT completed the Flash!
7. Press OK after download complete; satellite receiver will reboot by itself.
Do not interrupt satellite receiver until reboot by itself.
8. Go to the stb_gtools folder and click the gTools icon. This will open up the gTools program that will download the channel lists. Go to top left corner of the program and select FILE then OPEN and select the (dish500 with fav and bell (great lakes area) that is located in the stb_gtools folder. Select the satellite that you will aim the dish at... (Dish Network is E8.6 the 110W satellite and E7 is the 119W satellite.
Note: If you have a Dish 500 dish than you can download both. It will pick up both satellites!!
On the far left pane, Rite clicks the one you want and go to TOOLS then STB Connect. A window will pop up. Select download. Do not interrupt while downloading. Make sure your Computer says "Download Complete", not just 100%. If you don't get "Download Complete" you have NOT completed the Flash!
8. Connect your receiver to the Dish. THE CABLE IS PLUGGED INTO THE "IF INPUT" PORT ON THE BACK OF THE RECEIVER! Plug the other end directly into a LNB on your Dish.
9. Then on the receiver got to installation, then antenna setup (all passwords are always 0000).
Select satellite you want on the left pain. (Dish Network is E8.6 the 110W satellite and E7 is the 119W satellite. Still in antenna setup (on the rite pane) set LNB to "Standard" and freq to 11250. (This MUST be done to receive a QUALITY signal from the Satellite). Select transponder (TP) #11 for 110 (Echo 8.6) or #17 for 119 (Echo 7) (whichever you are looking for). (This MUST be done). Now leave the receiver on this screen while you set up the dish.
10. Now set up your dish. 110 or 119 is not the number to point dish with, with a compass. The Azimuth is. To find you Azimuth in your area go to the (Dish Network Dish Pointer) folder and click the ZipCode32 icon. Type your zip code in on the zip code button. Then on the left select the satellite that you want to point at. (E8.6 is the 110W satellite and E7 is the 119W satellite). Rite down the Azimuth and the Elevation angle. Now with a compass, point the dish in the direction of the azimuth number you wrote down. Now set the up and down angle on the dish to the Elevation angle you wrote down. There should be a meter on the side of the dish to determine this.
11. Go to the receiver and look at the quality meter at the bottom of the screen. Keep moving the dish little by little till you get a reading. Then get it a high as you can by moving the dish ever so slightly. When good, tighten all the screws on the dish so it wont move from the wind and stuff.
12. Now go to Satellite scan just above the Quality signal meter and scan all. The receiver will start to lock all the channels in (Are you getting exited?!!!!!) This will take awhile but is well worth the wait.
13. Go to parental control menu and at the bottom of the screen you should see "Second PIN" available. Enter "0000" and it will take you to a screen where you can turn the KEYS ON. Select ON (This activates the keys in the x-8500 flash, to decode the signals). This cannot be done until you have channels in your receiver.
14. Now here is the most important part………..
WATCH TV!
You can now go back to your channel list and delete all of the channels that do not have a $ in front of them, they are "Ghost Channels".
Enjoy
P.S.
…. FREE TO AIR ROCKS !!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
| Posted on Tuesday, February 22, 2005 - 08:21 pm: |
|
I GOT IT
I finally got my system working and it is your falut. Thanks to LK, Jim Millard and many anonymous contributers.
On January 29 Stephen posted a request in this forum that I would like to see come to pass. He asked simply for a easy to read index for newbies. I wish that I had saved all of the URLs that I had to chase down to find my problem. All of you showed great patience with me and guided me through a difficult time. Thank you again, from the bottom of my heart.
The fisherman@iname.com
|
|
| Posted on Tuesday, February 22, 2005 - 08:26 pm: |
|
OOPs, forgot. I hate to send an e-mail and then remember what I wanted to say. A neighbor just moved in next door and gave me the old D*V 3LNB dish in the yard. I read somewhere that this dish won't work with my Pansat for Dish. If anyone remembers where an article on that is it would save me hours of searching. I wish I had saved all of those URLs. fisherman@iname.com |
|
| Posted on Tuesday, February 22, 2005 - 08:55 pm: |
|
DTV triple LNB is NOT recommended...oval 2 LNB is Much easier and recommended...I believe I gave U or someone else here links to dsscommunity posts regarding this 3 LNB issue..read this ..copy/paste the link and remove the * from the .net
http://dsscentral.ne*t/forums3/viewtopic.php?t=2507 |
|
| Posted on Wednesday, February 23, 2005 - 07:39 am: |
|
Thanx again LK. You are the man with the plan and you are right there with the answer. It is now five am. I have been sitting here alll night trying to make some sense out of all the data out there on the web. I now know that the 3LNB setup can work for certain criteria since the center LNB is switched to cut out most the top of 110 but if it is as I read then I won't miss anything because I edit all the local stations out of my list before I upload it anyway. I don't care about Chicago, or Atlanta, or even God knows where in Tennesee. I even edit the California stations but I do add the Tucson stations using Channel Master and gTools. Now I have this question.
I am still stupid. I have a plain old DTV 18" dish with a 'dual' LNB, that means two outputs from one LNB. I have it pointed at 119 and am getting great reception.
A neighbor moved out and the apartment manager threw their dish away. I was at the dumpster and got a one year old Triple-feed 3 LNB 22" oval dish for free. I want to hook it up to get 110. I am not at all interested in East coast programming or Canadian so I have no desire for 91. I would enjoy 101 if I could get 3ABN. I have a new Pansat 2500a.
I am a newbie. I have only had reception for three days after working around a forty foot tree three hundred feet from my back door. Living in an apartment made a work around a real joy.
I am thinking of putting my new dish on the same pipe I had to have installed. This would give me two dishes, my 'dual' LNB at 119 and the three LNB at 110 and 101. Is this doable? Also, please explain SKEW I am using the base mounts clamped to a eight foot long one and a half inch pipe diameter bured in the ground eighteen inches with concrete around it. I put down an eight foot brass rod to ground the whole mess. Now, if I tilt the base mount off of plumb by the amount of the angle I compute for my dishes will that set the SKEW.
Please explain if my thinking is still fuzzy. Lord knows we had enough fuzzy durng the campaigns last fall. Thanx in advance for your help. fisherman@iname.com |
|
| Posted on Wednesday, February 23, 2005 - 08:40 am: |
|
Complete setup and how to guide, step by step instructions and STAFF support each and every customer.
www.fta-software.com
Others keep trying to copy but nothing is as good as the original source for all FTA software. |
|
| Posted on Thursday, February 24, 2005 - 03:18 am: |
|
Hello, stupid here again. Everything I read on dish setup refers to SKEW. I spent a solid fourteen hours last night searching every web site I could find on SKEW. I went to bed at nine this morning and am back at it at. All these sites tell me how to set elevation and azmuith, no big deal there any thirteen year old boy scout can shoot an azmuith or figure the elevation. These forums tell me to be absolutely sure that my mast is plumb and perpendicular then to set the dish and set the SKEW. HOW??? My two dishes have no sideways cocking adjustments. Do I tilt my mast by 8.3 degrees to the left? I live in Tucson, lat 32.21; long 110.88. Echo 7 is set at 194.1 with elevation of 51.5 degrees. Echo 6 is straight south of me at 178.3 with a 52.5 elev and a -1.4 SKEW. To put AMC 4 on this dish I need to aim at 161.9 w/ 51 elev and -15.2 SKEW or a total of 8.2 counterclockwise SKEW looking from behind. Is this correct? Can I tilt my mounting mast for this or is there something I am missing. Either way I still have not brought in the 101 AMC bird.
How about it Jim, or LK. I am here again asking. I am tired of searching and getting only the same old answers. I want to know HOW not WHAT. Okay??
The fisherman@iname.com |
|
| Posted on Thursday, February 24, 2005 - 09:29 am: |
|
Fisherman I've seen some kind of skew add on that you can add on to a dish without skew adjustment. Just can't remember where! I'll have a look. |
my2cents Unregistered guest |
| Posted on Thursday, February 24, 2005 - 10:39 am: |
|
fisherman your wasteing your time on all this searching etc. just take awalk around the neighborhood,pick up a used dish for a couple bucks with a skew built in.U can't adjust a dish's skew if it don't have the bracket.Moving the mast is not going to work. It just becomes too much of a headache.These dishes are designed to be accurate.....my 2 cents |
|
| Posted on Thursday, February 24, 2005 - 11:15 am: |
|
Hey thanx for the post. I couldn't sleep again last night so I just returned from a long walk. I found a DTV man installing a dish, at 7:30 in the morning. The new dish he had does have a SKEW adjustment on the back. Neither of mine do. He says to SKEW the twenty inch dish is to screw my mind. He says aim it at one or toss it. Looks like what you two guys are saying. Damn, I wish I could learn all of this the easy way. I guess I could just have someone install it but where would be the fun and agravation? The fisherman@iname.com |
|
| Posted on Thursday, February 24, 2005 - 09:10 pm: |
|
fisherman..
How to calculate and use Skew:
Skew= vertical offset (twist) in degrees from the vertical (from the 90 degrees mark on your dish)
1. Go to Satellite Nut page
2. Enter your location info.
3. Calculate skew for the 2 outter satellites on your dish (for the pansat setup on Phaze3 (oval 3LNB DTV dish) that would be 91 and 119)
4. Add them together and divide by 2
5. U get the skew number. (Disregard the minus sign if its negative)
To use SKEW:
You must ensure that the top of the mast is perfectly plum. Best thing is to use an eye round level (home depot,tools section - $3) that u put right on top of the mast. You do that BEFORE you even put the dish on the mast.
If you are on the EAST coast, skew = counter-clockwise rotation in degrees from the 90 deg mark on your phaze 3 dish. Set your dish to 90 minus the skew number
If you are on the WEST coast, skew = clockwise rotation in degrees from the 90 deg mark on your phaze 3 dish. Set dish to 90 plus the skew number
|
|
| Posted on Friday, February 25, 2005 - 12:49 am: |
|
Well thanky, thanky, thanky. I am up and running. The installer I told you about traded dishes with me. He had one he had taken down and it would go to junk. I put it up with who knows which LNB aimed at 110 with a counterclockwise skew of 11. I downloaded a channel list, working5_Legacy version, I added the Tucson locals and have tv. Problem, you knew there would be one so here it is. 1.)I have no sound on one station, local NBC affiliate. 2.)All of my sats disappeared from my setup program so I don't have the ability to search for another sat. I have no idea where the other LNB on the DTV triple header is pointed. I skewed as if aiming at 101 but I don't have any sats in the setup program to be able to do a scan of any kind. What happened to them? Did the channel list I loaded erase them? Before I loaded the list I did a complete back to basic boot load of my system. Everything was there then I did the upload into the box of the list. Short of going to a boot load again is there a way of getting a sat list so I can scan?
As a side, this one's freaky. I was listening to the radio last night, the 50s selection, okay, I'm old. I pushed the radio/sat button on my remote and my system went down. I checked it out and my keys were gone. OO was non-existant and 01 was jibberish. I resat 01 but could not even get to 00, hence the reboot of the system. Have you heard of that one before? Man there is a lot to learn with this hobby. It can keep a man busy. I like it because it keeps my mind occupied. By the way, have you seen my mind anywhere? I think I lost it. The fisherman@iname.com |
|
| Posted on Friday, February 25, 2005 - 09:14 am: |
|
U don't do an scan and add a channel list...its one or the other.. |
my2cents Unregistered guest |
| Posted on Friday, February 25, 2005 - 09:29 am: |
|
Fisherman start from scratch, flash with factory bin, then newest bin. Don't bother with channel lists there nothing but a pain in the azz. Just scan. The channels move occasionally thats why they turn up scrambled once in awhile.Bring in each sat seperatly then put on your switch. Do your own channel editing with the remote. Then if you want to save them you can for next time. good luck |
Unregistered guest |
| Posted on Saturday, February 26, 2005 - 09:47 am: |
|
Hi Guys, another Newbie here. My name is Bob. I have been reading through all the posts for a few days now and researched this and other websites. I am at the point of purchasing and was looking for recommendations. I am looking for 3 Pansat 2500a and 1 dish to pick up the 2 main Satallites (110 and 119?). I believe I would need a dual LBN dish with the ability to split to three seperate TVs.
Does anyone have recommendations on where to purchase? I have seen http://www.pansat.tv/ and http://dss-jmvip3mfiles.com/.
Any help would be appreciated on:
1. Where to purchase?
2. Satellite Dish models?
3. If what I stated in the first paragraph makes logical sense?
Thanks,
Bob S.
|
my2cents Unregistered guest |
| Posted on Saturday, February 26, 2005 - 10:10 pm: |
|
Bob S. the best FTA ird going right now is the Coolsat 4000+ or 4000PRO .depending on your budget and needs. Check'm out on fleabay...you won't be disappointed.
|
Silver Member Username: Jmill1948
Chester,
Va
Usa
Post Number: 546
Registered: Apr-04
|
| Posted on Saturday, February 26, 2005 - 10:29 pm: |
|
coolsat seems the way to go..............many features the fta era is opening up........... |
|
| Posted on Saturday, February 26, 2005 - 10:40 pm: |
|
--------------------------------------------------------------------------------
Coolsat 4000 Pro
-New Model for 2005-
For sale now on www.efta.us , order yours today!
The Coolsat 4000 Pro is an improvement on an already superb product line, its predecessor the 4000 Plus has excellent video quality and working EPG (electronic program guide) for Dishnet and BEV.
The main difference between the Pro and the Plus is that in addition to the outstanding quality and great hardware and firmware features of the Plus model, the Pro also has Dolby Digital (AC-3) audio output and S-Video output. The Pro also has dual composite A/V jacks (A.K.A. RCA jacks). The additional outputs improve audio and video decoding and quality as well as add versatility to the unit for use with almost any audio/video display system from a standard TV hook up to the most advanced home theaters.
With the best video quality available in a free to air receiver and new improved hardware you can see why we say the Coolsat 4000 Pro is the HOTTEST receiver on the Free to Air market today! |
Unregistered guest |
| Posted on Sunday, February 27, 2005 - 12:51 am: |
|
Hi! I'm from Saskatchewan and am currently under a Star Choice dish. I only heard about PANSAT today. I'm sorry guys, I've read over alot of these posts and am still confused about one thing... If I was to get a PANSAT could I just hook it up to my Star Choice dish? and is that illegal? Is there a certain dish you must have in order for a PANSAT to work. Any feedback would be greatly appreciated. |
|
| Posted on Sunday, February 27, 2005 - 10:05 am: |
|
illegal...its illegal if U "modify" and flash or insert any software into ANY TV receiver device or equipment that enables/causes it to receiver "encryted" (coded) signals such as Doishnetwork or Bev..so use of any particular dish,does NOT make it illegal,its what U do with the receiver that does..U can use many various dishes with FTA (pansat,coolsat,fortec)..go read the Dish info area at www.dsscommunity.com ..how many and which satellite signals (61.5,91,110,119,120 etc),how many receivers etc all are factors to use in determining the best dish for you...the simplest setup is an old DTV single LNB round dish pointed to the 119 satellite for use on 1 receiver. |
|
| Posted on Sunday, February 27, 2005 - 10:27 am: |
|
here I found this ...regarding starchoice dishs
Yes you can as the fta receivers use ku band lnb`s. I have the round 36" starchoice with the eliptical motor attached to it an works fine. Just make certain you enter the right freq. for the lnb. |
manyauru Unregistered guest |
| Posted on Tuesday, March 01, 2005 - 12:02 am: |
|
on february 4 i ask for help on information how get subtitles for movies and movies time on my pansat 2500aif you would be so helpful to send this information that be a great help thank you |
|
| Posted on Tuesday, March 01, 2005 - 12:10 am: |
|
U cannot get EPG (extended programming guide) with your Pansat...no subtitles,program guide,times etc...EPG ONLY works on the coolsat 4000, NOT any Pansat.. |
|
| Posted on Tuesday, March 01, 2005 - 12:19 am: |
|
and with the coolsat (ONLY):
With some movies there is too much information to fit in the EPG display window. When this happens just hit the audio button, the green one. This will let you read the rest of the info. |
Bronze Member Username: Dtvmaster
Usa
Post Number: 51
Registered: Jan-04
|
| Posted on Tuesday, March 01, 2005 - 07:43 pm: |
|
coolsat 4000 recievers 360.00 Pre programmed with support Gets all channels and epg Guide on Boxes Pansat doesnt Recieve that feature. email Cabletec123@aol.com for all orders Phone and Via email support Available now |
loaded LK Unregistered guest |
| Posted on Tuesday, March 01, 2005 - 07:55 pm: |
|
Wow LK ! You own a coolsat 4000? you must be loaded..
|
|
| Posted on Tuesday, March 01, 2005 - 08:42 pm: |
|
?????????...I never said that I EVER owned anything!...ownership of devices used/modified to decypyt satellite signals is illegal...never said that I have ever tested DTV,Dish or FTA either...I just like to read....my posts are for educational and informational purposes only.use for any illegal activities is strictly prohibited... |
|
| Posted on Wednesday, March 02, 2005 - 10:56 am: |
|
hah....thats really funny . 
|
|
| Posted on Wednesday, March 02, 2005 - 12:20 pm: |
|
Hi I'v been reading the post listed on this site and they have really helped me a lot. But there is still one point that I am stuck on. I have TV. I downloaded a ben and used the key. But this channel list thing has me stumped. Once I go to the channel list and view it, what is the next step to use it on my TV?? I don't think that I am getting ALL the PPV's that I read you guys have(I have 6). Thank You In Advance. |
|
| Posted on Wednesday, March 02, 2005 - 05:55 pm: |
|
use the channel list with Gtools program..in fact Jmil has a video of it..look around and read some posts..I saw it posted within past 2 days.. |
|
| Posted on Wednesday, March 02, 2005 - 06:12 pm: |
|
copy/paste from the other thread...it has Gtools and how to add channel list..
--------------------------------------------------------------------------------
http://www.dss-jmvip3mfiles.com/Download%20Files.htm
look on this webpage for the pansat blacklist updater and gtools downloads.
this is the ultimate download you will need for pansat 2500a flash. its so easy, just make sure you have separate lnbs on your dish. built in switches on your dish will not be compatible with any fta receivers. this is the only flash you need, no codes, no bull . take care, let me know how it goes. tim |
Bronze Member Username: Jmvip3mfiles
USA,
USA
Post Number: 41
Registered: Mar-04
|
| Posted on Thursday, March 03, 2005 - 02:42 am: |
|
EPD GUIDE Working
Http://www.dss-jmvip3mfiles.com
Http://www.dss-freetoair.com |
Channel Guide Unregistered guest |
| Posted on Thursday, March 03, 2005 - 01:12 pm: |
|
Is the channel guide the same as the one on Dishnetwork ?
|
Silver Member Username: Jmill1948
Chester,
Va
Usa
Post Number: 551
Registered: Apr-04
|
| Posted on Thursday, March 03, 2005 - 03:00 pm: |
|
not the same but very good one.........coolsat the future |
Matt Thiery Unregistered guest |
| Posted on Thursday, March 03, 2005 - 05:24 pm: |
|
Hello. I purchased a Pansat 2600 a month ago because dealer told me it was the ultimate final option. and now there's this new Coolsat 4000 thats much better and it even has a channel listing. I feel betrayed by the dealer like I threw $250 away. Hope this never happens to you.
|
|
| Posted on Thursday, March 03, 2005 - 06:06 pm: |
|
Pansat 2600?...U mean 2500..and U paid $250,then U got screwed..$150-$170 is average..and a month ago coolsat didn't have a working EPG (program guide)...thats only 1 week old,the EPG software release..
BTW...pansat2500 for $150 or so is still a very good receiver.. |
|
| Posted on Thursday, March 03, 2005 - 06:23 pm: |
|
LK....Thanks for clearing that issue up. I had the same feelings about the news of coolsat. I didn't know that the improvements were only a week old. I wondered why i had not heard about this wonderment before. I got my Pansat 2500A in december and for around $165.oo (shipping included) I still feel like I got a deal. I'm NOT running out and buying the coolsat. I will live out the life of my investment with my Pansat., Thanks Again...Kilroy |
|
| Posted on Tuesday, March 08, 2005 - 11:19 pm: |
|
hi everyone! It appears charlie has gone down.Could some kind soul direct me to a web site with fix. Al7bar seems to have disapeared thanks |
|
| Posted on Tuesday, March 08, 2005 - 11:26 pm: |
|
Read this link..it'll fix U right up!...next time,take 10 seconds and READ before U post!
http://forum.ecoustics.com/bbs/messages/2/126322.html |
|
| Posted on Wednesday, March 09, 2005 - 10:43 am: |
|
LK...since you have the most knowledge about these things and you are willing to help, may i ask your help on this....please... I was trying to change the code key on my pansat 2500a and one of the letters doesnt work. Is there any other way to change the |
Closed: New threads not accepted on this page