| Author |
Thread: DTV and DN Sat dish Compatibiity |
    
New member Username: 108warrior
Chicago,
IL
USA
Post Number: 1
Registered: Sep-07
|
| Posted on Monday, September 03, 2007 - 09:14 am: |
|
Do DTV 3LNB dishes work with FTA receivers?
I have a viewsat ultra and was attempting to connect to a DTV AU9 Dish with 3 LNBs, but did not receive a signal. The receiver does work but I was considering getting a Dish with multi LNB's. If it does not are there any recommendation? |
|
|
|
Platinum Member Username: Lklives
Post Number: 11584
Registered: Jan-06
|
| Posted on Monday, September 03, 2007 - 02:14 pm: |
|
yes U can get 1 DN and 1 Bev sat on FTA, with that phase 3 DTV dish...and u will no longer get DTV....do a search here of phase3 ...
Much simpler just to buy a Dish Pro 500 TWIN LNB dish for $69... |
Gold Member Username: Nydas
Post Number: 3574
Registered: Jun-06
|
| Posted on Monday, September 03, 2007 - 03:26 pm: |
|
Here is a list of sites where you will find a lot of information. It has been modded. from a list published here.
Future FTA - Blacklist's Site:
http://www.future-fta.info/forum/index.php (Pansat)
FTA Tech - Free To Air Community:
http://www.ftatech.net/forums/ (All receivers)
Free To Air:
http://www.f2atv.com/ (C00LSAT and All receivers)
DSS Newbies:
http://www.dss-newbies.net/forums/ (All receivers)
DSS Rookie:
http://www.dssrookie.com/forums/ (All receivers)
Total FTA
http://www.totalfta.com (VIEWSAT and All receivers)
FTA Support
www.ftaprosupport.com (all receivers)
Cut and Paste these into your browser:
REMOVE the * in links below: This site allows downloads of files without registering.
http://forums.dsstester.c*om/ (All receivers)
This site is agood alternative site for Pansat and Pansat clone files.
http://www.al7bar.t*k/ (All receivers)
This site was free but now has a small fee for files, but is the best site for Clone receivers in general..
http://www.pantecf2a.com/support (Pantecs,all clones and all receivers)
File Share Site - No Registration Required:
--------------------------------------------------
Good for gettting Original factory firmware:
http://www.ftacentral.c*om/ (All receivers)
Satellite Finders (Look Angle Calculators)
-------------------------------------------------
http://www.arachnoid.com/satfinder (Dish 500 support)
http://www.satellitenut.com/calculators/SatelliteHeading.html
http://www.hollsco.com/Products/SatCalc/
http://www3.telus.net/rampage/skew.htm (Dish 500 support)
http://www.remotesat.com/lookangle.htm
Satellite Charts
--------------------------------------------------
For information on all satellites and channels they offer
http://www.lyngsat.c*om/america.html
http://www.satcodx.com/
Best site for DISHNET info, channels, transponders and changes etc..
http://ekb.dbstalk.com/dishlist.htm
Direct links to current Dishnet and Bev keys:
www.tvkeyz.com/
www.dss-keys.com/
www.fta123.blogspot.com |
Gold Member Username: Tapeman
New York City in-HD,
NY
Post Number: 1311
Registered: Oct-06
|
| Posted on Monday, September 03, 2007 - 08:02 pm: |
|
- Yo need to set LNB to universal
- If you point middle LNB to 101 (you'll get 91 and 110)
- If yo point to 110 (you'll only get 119)
- Yo'll never get 110/119 with these LNBs (either or)
- The reason is Middle LNB has an internal block to most higher transponders) It will allow yo to get 3 or 4 transponders with very limited channels on middle LNB |
|
