| Author |
Thread: 2700a |
    
|
| Posted on Sunday, April 17, 2005 - 10:15 am: |
|
i have a pansat 2700a that is dead i loaded two bin files on top of each other now the receiver has no power. can anyonr help? |
|
Relevant Product Info
|
|
|
| Posted on Sunday, April 17, 2005 - 11:14 am: |
|
try unlugging for few hours...then put factory bin back on...also can try reset/reboot first (Back of receiver,power OFF,wait 1 min,power ON)
|
|
| Posted on Sunday, April 17, 2005 - 11:15 am: |
|
try unplugging for few hours...then put factory bin back on...also can try reset/reboot first (Back of receiver,power OFF,wait 1 min,power ON)
|
|
| Posted on Sunday, April 17, 2005 - 11:20 am: |
|
Maybe this will help in future...
Here are a few tips if you are having difficulty flashing:
I would advise everyone to read a set up guide before flashing. But, since people have been having some problems, I have revised this to provide more detailed information. But this is not intended to be a substitute.
1. Make sure you use the proper serial cable for your receiver:
Fortec and Pansat use a straight through cable with DB9 females on both ends.
The Blackbird uses null (crossover) cable, which crosses over pins 2 and 3.
2, With the power turned OFF, connect it to your computer and receiver using the serial connector. Use serial port #! if you can.
3. If you do not have a working serial port, you must install one or use a computer that has one.
4. Use the appropriate loader.
5. Select the file. Make sure that it is the correct flash for your receiver.
6. Select the COM port your receiver is connected to. If you do not know, what it is try #1 first.
7. Enter the correct model name and number. ..example (pansat2500)
8. Check off the correct function box. Your choices are boot, flash or channel list. To FLASH your receiver you would use FLASH. Most flashes do not require a separate boot; so do not load both separately.
9. Turn ON the receiver power from the back switch. (so obviously it is OFF prior to this step)
10. As soon as you see the lights flash,very first light -- IMMEDIATELY press download.
11. Wait until it COMPLETES and reboots.
................................................................................ .........................................
Here is how to recover from the "Night Rider" (flashing lights):
1. Try re-flashing the factory boot/flash again using the above directions. That gives you FTA ONLY. Follow the above procedure.
2. Then, when that works use the latest flash (AUTOROLL) to get the scrambled channels.
3. Download a channel list and/OR do a channel scan on each sat.
4. When flashing, be sure to wait not only until is says done/complete. But you need to wait until it reboots and actually goes to a channel number. |
|
| Posted on Sunday, April 17, 2005 - 12:26 pm: |
|
Found this ,but I don't know how much truth there is to it....Could be BS,I have no idea.
ATTENTION..
DO NOT USE FORTEC ULTRALIFE AUTOROLL AND PANSAT AUTOROLL, IF YOUR RECEIVER IS A CLONE. IT WILL KILL IT WITH NITE-RIDER LIGHTS.
THERE WERE 2 FILES SAYING "NAGRA2" FOR BOTH FORTEC AND PANSAT ON SOME OTHER SITES. DO NOT USE IT-ITS FAKE..WAIT FOR AFTER APRIL 27....
|
Unregistered guest |
| Posted on Thursday, April 28, 2005 - 02:29 am: |
|
Does anyone know how to troubleshoot the pansat 2700a? I just installed it and I'm trying to enter the current keycodes. Whenever I go to 'parental controls'to get to the screen to put in the codes, it keeps prompting me to change my password again and again and again...
The only options on the parental control screen is: old - new - confirm new. Someone told me to go to "secondary password" and enter in my current password but there is no such option.
How do I get past this?
Am I overlooking something?
I've already flashed it with the "X-87BL_050315_101_api" bin file.
Please help.
Thanks.
|
|
| Posted on Thursday, April 28, 2005 - 12:15 pm: |
|
Go here...remove the * in .T*K
http://forums.al7bar.t*k/showthread.php?t=65920 |
|
| Posted on Thursday, April 28, 2005 - 12:19 pm: |
|
Chris the above is for U...it appears some of the 101 bins are corrupt..
Pansat 2700a setting key code manually
--------------------------------------------------------------------------------
I'm familar with manually setting the key codes on my Pansat 2500a. When doing the same steps on a Pansat 2700, I encounter a totally different Parental Control screen that I get and can't get past to where you enter the key codes as I've done on the 2500a. Are the steps to manual change the key codes different between the 2500a and the 2700 receiver?
toxsixski
View Public Profile
Send a private message to toxsixski
Find all posts by toxsixski
Add toxsixski to Your Buddy List
#14 1 Day Ago
jcghound
Title: Registered User
Rank: n00b
Status: jcghound is online now Profile
Join Date: Feb 2004
Posts: 15
hmm I've been waiting also to see if someone would jump in here and answer the mans's question as I also have the same question. I've been looking all over and see no posts addressed to accessing the CAS System Menu for the 2700A. I had assumed it was the same as the 2500A but have yet found a way to get a 2nd PIN Code to popup in the Parental Control. Have good type 4 list loaded, good signal and quality, good picture on free channels. Flashed the X-87 Bl 101 autoroll bin and done several hard reboots and can not get keys to roll. Does the box need to have the Key Code Fuction and Default Key turned on after loading the channel list like the 2500A. Someone point me in the right direction. Thanks
hound
jcghound
View Public Profile
Send a private message to jcghound
Find all posts by jcghound
Add jcghound to Your Buddy List
#15 19 Hours Ago
jcghound
Title: Registered User
Rank: n00b
Status: jcghound is online now Profile
Join Date: Feb 2004
Posts: 15
After a couple of hours of research and reading numerous posts including other forums I have found the answer to the problem I was having with accessing the CAS System Menus. Hopefully this will help some of you having the same type problem.
First of all, any channel list downloaded needs to be a stb type 4 list downloaded with the mod gtool done by BL ver 1.8 for the 2700. Using any other tool will corrupt the echostar package in the bin and although the channels appear to work the autoroll s/w in the bin will not work right. Second, there appears to be several versions of the X-87Bl 101 bin floating around with both having same name and version number. One will work and the other will not. My friend did not download his version here and it appears he picked up a bad version elsewhere. With the correct bin and proper type channel list loaded with the correct tool, the CAS System Menu access will work the same as for the other pansats.
This one was a little difficult to put a finger on as there were two things going wrong and the unit appeared to work correct by being able to pick up clear channels indicating the channel list loaded correct although it wouldnt get scrambled pictures and there was no 2nd PIN showing up in Parental Control to access the CAS System Menu.
|
|
| Posted on Thursday, April 28, 2005 - 12:27 pm: |
|
anyone know anything about digiwave 7000? |
|
|
|
| Posted on Thursday, April 28, 2005 - 06:58 pm: |
|
what does this have to do with the thread topic 2700?....NOTHING!....so suggest U either post correctly,if U want help or go to another site and read their threads and topics in the forums..
go here and don't ask anymore about the digiwave...its the only place with the info U seek..remove the * in .T*K and register there too..
http://forums.al7bar.t*k/forumdisplay.php?f=138 |
New member Username: Barabashka
Post Number: 1
Registered: May-05
|
| Posted on Saturday, May 07, 2005 - 03:23 pm: |
|
Hello every body . I have pansat 2700a , what i have to do to start the programming???Please any HELP HELP HELP |
|
| Posted on Saturday, May 07, 2005 - 04:14 pm: |
|
does anyone know the stb model key for PS 2700? I already have the file |
|
| Posted on Saturday, May 07, 2005 - 04:17 pm: |
|
does anyone know the stb model key for ps 2700? i already have the file |
|
| Posted on Saturday, May 07, 2005 - 04:30 pm: |
|
global |
|
| Posted on Saturday, May 07, 2005 - 04:38 pm: |
|
It not working! only work for 2500! It there other something ### ? |
|
| Posted on Saturday, May 07, 2005 - 04:40 pm: |
|
Pansat 2700 or global...otherwise SOL |
|
| Posted on Saturday, May 07, 2005 - 04:46 pm: |
|
more likely SOL, thanks |
|
| Posted on Saturday, May 07, 2005 - 04:48 pm: |
|
Setting up the Pansat 2700
This will be a brief down & dirty “How to” for the 2700 with files included.
Lets get at it,
Download the attached file 2700a.zip to your PC and unzip to a folder of your choice.
Remove Pansat 2700 from box. Attach to PC via RS232C null modem cable.
From the folder you unzipped files to, start & run the application GTRom Loader v3[1].35 [pansat2700A]
Click “Bin File” and select the 2700 autoroll bin X-87BL_050315_101_api(N)_
Turn your 2700 on via rear switch. When you see the first green LED light up, Click “Download”
Wait for unit to finish flash, DO NOT INTERUPT!
When receiver reboots and displays “ON” proceed to next step of loading a channel list
NOTE; The channel list provided is working5 by Wingnutt101 for LEGACY lnbs ONLY
To load a channel list on your 2700, start & run the application Ch Editor187 (Pansat 2700A)
When Pansat Channel Editor 2700a appears, click file, open, select the channel list working5-legacy-2700
At the top of the screen click where it says “Tools” and goto “Connect to receiver’ Then click “Download”
Wait till finished and unit will reboot to channel 001. Your Pansat 2700 is now flashed and a Legacy Dishnet channel list has been loaded.
Disconnect receiver from PC and install to dish & TV connections.
Enter “Menu” and goto Antenna setup and make the necessary changes of the DiSEqC settings to match your own configuration.
Exit menu and select Channel 300, The “Downloading Data” should appear on your screen, and after a few minutes (up to 10 minutes) TV should appear.
Enjoy your new receiver J
|
|
| Posted on Saturday, May 07, 2005 - 05:25 pm: |
|
I about to give up! but thanks, next where can i find XXXXto download the channel list?
|
|
| Posted on Saturday, May 07, 2005 - 05:44 pm: |
|
no needed, thanks, SOL |
|
| Posted on Saturday, May 07, 2005 - 07:33 pm: |
|
Do a scan instead.. |
New member Username: Barabashka
Post Number: 2
Registered: May-05
|
| Posted on Saturday, May 07, 2005 - 08:47 pm: |
|
Wheare can i get that "X-87BL_050315_101_api" bin file |
|
| Posted on Saturday, May 07, 2005 - 08:54 pm: |
|
Every reputable Dss site that has a file area.... |
|
| Posted on Thursday, May 12, 2005 - 08:56 pm: |
|
Got a brand new 2700A. I am trying to use my old direct tv dish I get 85% signal strenght but 0% quality. On the advance scan screen I can see the satellite i selected but it says unlock on top.
Any ideas what can i do to improve the quality of the signal |
|
| Posted on Thursday, May 12, 2005 - 11:14 pm: |
|
Have U flashed it with the 101 bin,then do the scan and reset the receiver,as explained above?..the files are located at www.al7bar.t k |
New member Username: Barabashka
Post Number: 3
Registered: May-05
|
| Posted on Friday, May 13, 2005 - 06:11 pm: |
|
Hello, Any body now a key for ADULT CHANNELS????I have PANSAT 2700 + dISH |
Silver Member Username: Maple_leaf
Post Number: 281
Registered: Apr-05
|
| Posted on Friday, May 13, 2005 - 06:56 pm: |
|
Gone can't get no more. |
|
| Posted on Friday, May 13, 2005 - 08:38 pm: |
|
people...U better stop asking dumb questions or U will get NO help from anyone...KEYS are for Dishnetwork,not particular channels..even someone who doesn't hobby with FTA knows that...so this BS has to stop,or all will end up paying the price.. |
|
| Posted on Sunday, May 22, 2005 - 05:04 pm: |
|
these are the latest firmware
X-75BL_050314_236cE_api------for pansat 2300A
X-85BL_050405_246_api----------for pansat 2500A
X-85BL2_050330_245_api--------for pansat 1500A
X-87BL_050519_105_api----------for pansat 2700A
X-95BL_3033_2005_0425_api--for pansat 5000HC
they all autoroll. and the 2700a has a working (epg)!
|
catchdvapor Unregistered guest |
| Posted on Monday, May 23, 2005 - 09:35 pm: |
|
Can someone tell me if a triple lnb directv dish will work with a pansat 2700a? If so what sat should I point to? |
|
| Posted on Monday, May 23, 2005 - 10:25 pm: |
|
this thread is about the 2700,NOT about DTV dishes..so post in the correct place next time,or start a new thread..READ the new Ecoustics RULES thread here..
If U must ask what satellite(s)to point at,then FORGET using that particular dish,..its VERY VERY complicated to align..
BTW...a receiver is a receiver,the make/model of the receiver has nothing to do with the type dish!...any FTA will work on just about any dish.. |
|
| Posted on Thursday, May 26, 2005 - 01:11 pm: |
|
need advise on 2700a pansat. while watching tv my system start to download files upto 600% reboot by it self and on channel display window it showing -6.2- and turn off. try to reflashed with factory bin still -6.2- still showing, try reflashing on 2nd time green light. unplugged my system for couple of hours still no luck. what the hell is -6.2-? |
New member Username: Dede2005
Post Number: 1
Registered: May-05
|
| Posted on Saturday, May 28, 2005 - 02:03 pm: |
|
I have a problem with my Pansat 2700A, i connected it on my computer and i open my GTRom 3[1].35 and i select the latest firmware and then i go to download and it keeps saying "flash update fail ..." and i tryed it on all serial ports its like my computer can't detect that its connected or sumthing i dunno, i have a windows xp operating system |
|
| Posted on Saturday, May 28, 2005 - 06:10 pm: |
|
U have the wrong cable...need null modem not straight cable D9 female.. |
New member Username: Dede2005
Post Number: 2
Registered: May-05
|
| Posted on Saturday, May 28, 2005 - 07:13 pm: |
|
well im using the cable that came with my pansat, and in the GTRom loader theres only the selection between COM1 to COM4 so isint that like a serial port? |
|
| Posted on Saturday, May 28, 2005 - 09:43 pm: |
|
U have the wrong cable...need null modem NOT straight cable D9 female.
Attach to PC via RS232C null modem cable |
New member Username: Dede2005
Post Number: 3
Registered: May-05
|
| Posted on Sunday, May 29, 2005 - 12:32 am: |
|
ok and do i connect that cable the same place i had the other one conected or what kind of thing do i need to conect that on? sorry im new to this is there like a modem of sum sord i need to buy to conect the null thing on or do i use the same COM ports with that cable |
|
| Posted on Sunday, May 29, 2005 - 01:59 am: |
|
yes hook it up the same way.... |
hollaback9 Unregistered guest |
| Posted on Monday, May 30, 2005 - 10:05 pm: |
|
Is X-87BL_050519_105_api(N).bin the newest file for the 2700? My last file I tried was X-87BL_050315_101_api(N) and I scanned on echo 7 and 8.6 and it was showing channels during the scan but when complete showed "scrambled channel" on the screen. My location and quality are above 80%. I'm using the oval 23'directv with dual lnbs. Do I have to go to channel 300? or just do a blind scan? |
|
| Posted on Tuesday, May 31, 2005 - 09:41 am: |
|
105 is latest for the 2700..blind scan,then a reset.. |
|
| Posted on Monday, June 06, 2005 - 08:51 am: |
|
Kneegrow the Mod here!
Now that Kneegrow has surfaced here again (was probably on paid vacation), have U noticed:
Analman returned
Larry Doherty returned
Punjavi returned
More thrashy disgusting "unregistered" posts
There is a campaign to get rid of me and Maple Leaf
Your posts are getting DELETED (many/most of mine) BUT NONE of his (Kneegrow) or his aliases and other "unregistered" thrashy posts..
Now tell me,that Kneegrow is NOT an Ecoustics mod, paid to create havoc here,play the clown,entertain,run these forums so as to draw internet hits for google for the sponsors and Ecoustics,and delete informative posts to save bandwidth and keeps people coming back to ask the same questions over and over (more internet hits at 10 cents each = alot of money),...ITS ALL SO OBVIOUS!...HE'S A MOD HERE!...and a SNITCH/MOLE for DTV,Dishnet,BEV and the FCC...U all think he's funny,but he's got your IP logged and your email addy (if U're stupid enough to register here)and handing it over to the authorities... |
|
| Posted on Saturday, June 11, 2005 - 05:17 am: |
|
Im using a pansat 2700a and it freezes during auto roll. usually gets between 500% - 600% before it freezes. I had the X-87BL_050315_101_api(N) and thenput on the 105 and same problem. Anyone have a suggestion? |
|
| Posted on Saturday, June 11, 2005 - 05:29 am: |
|
I manually inputted the keys and it seems to be fine now. |
|
| Posted on Saturday, June 11, 2005 - 10:46 am: |
|
JLe - The same problem surfaced with my 2700A during the data download last Thursday night. It appears that Autoroll no longer works for the 2700A. What were the Keys (numbers) that you inserted to brting it back to operational status? |
|
| Posted on Saturday, June 11, 2005 - 11:35 am: |
|
Install the new autoroll bin for the 2700..just released today..www.dsscommunity.c o m File share FTA area. |
New member Username: Pietro347
Post Number: 1
Registered: Apr-05
|
| Posted on Sunday, June 12, 2005 - 12:36 am: |
|
does anyone have receiver testing manual for the 2700a please let me know where i could get it i need to jtag my receiver thanks |
|
| Posted on Sunday, June 12, 2005 - 12:48 am: |
|
al7bar.t k |
Bronze Member Username: Timscarlet
Dayton,
Oh
Usa
Post Number: 32
Registered: Feb-05
|
| Posted on Sunday, June 12, 2005 - 02:12 am: |
|
got to wwww.ultimatetesters.com for manuals and the latest pansat 2500 autoroll fix. |
|
| Posted on Sunday, June 12, 2005 - 08:06 am: |
|
Posted last Thursady...where ya been!
LK
Unregistered guest
Posted on Thursday, June 09, 2005 - 08:19 pm:
--------------------------------------------------------------------------------
All FTA autorolls,except the coo*lsat released last night, are down...Dish has done a minor ECM..atmega is also working..don't worry,nothing is broken or damaged...BUT new autoroll bins will be needed..
Just enter your keys manually
If you cant get into your menu because your FTA box is frozen downloading the new key, just turn your receiver off, then on, then immediately go into your MENU screen.
Thats it!!
BTW...there are new WORKING Pansat autorolls released Saturday morning at www.hashhu.com and www.al7bar.t k
Also the 2700 manual input of the keys is the same way as the 2500.. |
Bronze Member Username: Timscarlet
Dayton,
Oh
Usa
Post Number: 33
Registered: Feb-05
|
| Posted on Sunday, June 12, 2005 - 07:13 pm: |
|
WWW.ULTIMATETESTERS.COM HAS THE NEW AUTOROLL FIX ON 6-11-05 FOR PANSATS 1500, 2500, 2700 |
jason_gj Unregistered guest |
| Posted on Sunday, June 12, 2005 - 09:05 pm: |
|
hey, i got a problem, when i open the STB tool, on the firmware page, i cant detect the port, it keeps changing between com 1 and com 3...can someone help me?? This is for the pansat 2500a.. |
Unregistered guest |
| Posted on Tuesday, June 14, 2005 - 09:07 pm: |
|
i have the 2700a and it went down 2 days ago.brought back up by going into menu a d put the new numbers in manually.went down today,screen stuck on language and front of box reads On OR Dn. anyone have a solution? thx mcoramp |
Unregistered guest |
| Posted on Tuesday, June 14, 2005 - 09:07 pm: |
|
i have the 2700a and it went down 2 days ago.brought back up by going into menu a d put the new numbers in manually.went down today,screen stuck on language and front of box reads On OR Dn. anyone have a solution? thx mcoramp |
|
| Posted on Tuesday, June 14, 2005 - 10:58 pm: |
|
I need to know the Provider ID I need to enter on the 2700a under nagravision to enter de BellVu keys, I don't find BellVu in the provider ID list |
Bronze Member Username: Timscarlet
Dayton,
Oh
Usa
Post Number: 47
Registered: Feb-05
|
| Posted on Thursday, June 16, 2005 - 12:09 am: |
|
CD THAT HAS EVERYTHING YOU NEED:
AUTOROLL BIN FILES
PANSAT, FORTEC, COOLSATT, AND OTHERS
SOFTWARE TO UPDATE THESE RECEIVERS AND CHANNEL LISTS FOR DISH NETWK CHANNELS.
HOW TO VIDEOS AND PICS, STEP BY STEP TO INSTALL YOUR RECEIVER TO GET FREE DISH NETWK CHANNELS WIDE OPEN, PAY PER VIEW, MOVIE CHANNELS, ALL OF THEM.
IF YOU NEED THIS INFO I GOT FROM HOURS OF GATHERING FROM THE INTERNET, EMAIL ME, IT COMES WITH MY PERSONAL EMAIL SUPPORT. TIM |
New member Username: Dnyaj
Post Number: 1
Registered: Jun-05
|
| Posted on Friday, June 17, 2005 - 11:12 pm: |
|
I have a MultiStar Pantec Ultra ird, but when boot up it said Fortec Star. When i first has this unit about 3 weeks ago. It was able to autoroll. but now I have to manual input twices a day. Can anyone provide any information. also, i downloaded the new software ver 2.76, ver 2.74 is on my ird right now. Can I just update to ver 2.76. will it cause any harm? anyone can help it would be very appreciated.
|
Silver Member Username: Maple_leaf
Post Number: 416
Registered: Apr-05
|
| Posted on Friday, June 17, 2005 - 11:28 pm: |
|
Tim you are so full of it. |
|
|
